The customer complained that his Toshiba Satellite A70 laptop doesn’t have video on LCD but the screen lights up when he turns on the laptop.
Laptop diagnostics and repair:
The laptop started without any video on the LCD screen, but the backlight lighted the screen. When you have a problem like this, always try to connect the laptop to an external monitor. If the external video is fine, then most likely the system board or the video board in the laptop are fine and the problem is somewhere between the LCD screen and the system board. I connected the laptop to an external monitor and got a normal video output. To find the problem, I opened up the laptop display assembly and found that the video cable on the back of the LCD screen was half way out. After I reseated the display video cable, the laptop started with the internal video.
Read more:
How to troubleshoot and fix laptop video problems
Laptop has bad video on the LCD screen. What is wrong?
If you find this article useful, please consider making a donation to the author. Thank you!
June 19th, 2007 at 5:43 am
i tested it on an external monitor and the same thing came up.
so this means a new motherboard?
June 15th, 2007 at 10:35 pm
patric,
First of all, test your laptop with an external monitor. If you see the same wonderful mosaic on the external monitor, you have a problem with the video card. In a Toshiba Satellite M30X/M35X the video card is integrated into the motherboard, so you’ll need a new one.
If the external monitor works fine and this defect appears only on the internal screen, you might have a problem with the LCD screen or the video cable.
Just in case try reseating the video cable on both ends – the motherboard and the LCD screen. A loose video connection can cause many different video problems.
June 12th, 2007 at 5:31 am
if you look at the pic below, thats what i get on my screen after boot up.
http://www.imgshare.net/view_i.....osdied.jpg
May 29th, 2007 at 10:35 pm
Hey Lonnie,
I had the same problem after cleaning the A70 out. Good news: it’s an easy fix.
The problem is in the LCD screen circuitry. Fix the screen by:
Use something to pad the back of the screen where you pressed (I used several layers of electrician’s tape)
0) Boot up the computer
1) remove the securing strip
2) Let out some slack by gently pulling the wires from their channels
3) remove the two bottom rubber pads and the two screws beneath them (no screws under the top pads – leave them)
4) Remove the four F8 screws securing the screen hinges to the laptop body
5) Use a small screw driver or other suitable tool to gently pry the casing apart
6) remove the two top screws securing the lcd to the monitor casing
7) Finally – from the point where the screen has no picture, press gently at the rear top of the screen at that point – this should bring back the picture
9) Close ‘er up
Email me with questions if needed
April 30th, 2007 at 12:02 am
LonnieB,
Did you remove or unlock the CPU during the disassembly process? If you did, make sure the CPU is properly seated and LOCKED inside the socket.
If you have any extra memory stick installed remove it and test the laptop just with the integrated (onboard) memory.
You also can try this. Unplug the display video cable from the motherboard and test the laptop with an external monitor. If the laptop works with an external monitor when the video cable is unplugged, probably there is something wrong inside the display assembly.
If the external monitor will not work even with unplugged laptop display, something is wrong on the motherboard.
As a last resort, you can remove the motherboard from the laptop base and assemble it outside the box. All you need is: motherboard and CPU with the cooling module, the motherboard already has integrated memory. Test this system with an external monitor. If it works find, start assembling everything back and test the laptop after each step.
April 29th, 2007 at 8:09 pm
Hi,
I have a similar problem with my toshiba a70. I took it apart as I was having problems where the laptop was shutting down and found a solution with cleaning the heatsink. When I put it all back together I found no video on the screen. When I went to hold the power button to turn it off I found that the screen flashed. I took it apart again and went through all the cables and ensured that they were all connected, and put it back together again.
Any ideas? Screen was working find before.
April 22nd, 2007 at 2:49 pm
Tim,
Even though the screen is cracked in some cases it’s still possible to see some video on it. Did you check video before you replaced the screen? Did you check video on the external monitor, just to make sure the laptop itself works fine?
Try starting the laptop in Safe mode, maybe you have a problem with the video driver.
April 14th, 2007 at 1:39 pm
I have just replaced the lcd screen in my laptop but am now only getting a partial screen. It appears the right side of the screen is cut off and also has problem with the bottom of screen. This laptop was given to me a few days ago with a broken lcd but the vin plate on the bottom has no model or serial number. The documentation say its a a70/75 and the screen i bought was the repalcement part for the screen model number. I am just about to pull my hair out
February 24th, 2006 at 1:37 pm
The first thing that came to my mind – a bad LCD screen and I know how much new laptop LCD screen cost.
You say that the external monitor works fine, so most likely it is not a video driver issue. It is possible that the video cable is not seated properly and I would defiantly try to reset the video cable connectors on the system board and on the back of the LCD. Just in case try to re-flash or update the BIOS, who knows… It is also possible that the video cable is defective itself. You can also try to twist the LCD screen to create tension on the LCD, but not too much because you can crack the screen. Move top left and right corners of the screen in opposite directions. BE CAREFUL. See if you can get a normal video or if the vertical lines will disappear when you twist the screen, if yes then I would say the screen is bad.
February 24th, 2006 at 1:13 pm
My problem with my Toshiba satellite is similar to this one.maybe you could shed some light on this one. When turning on laptop only half of the screen appears. Screen is completely backlit with only several band of varying vertical bands. external monitors work fine and the laptop would still be usable to me if I could find someway to split screen to see remainder of screen. As im sure you know a new screen is really not cost efficient. Help this sucks>