Toshiba Satellite M35X and Satellite A75 power jack and battery charge problem
A bad connection between DC-IN power jack on the system board and the system board is a very common problem with Toshiba Satellite M35X and Toshiba Satellite A70/A75 notebooks. If your laptop is out of warranty, then you can fix the problem by resoldering DC-IN jack on the system board. If it’s still under warranty, it would be fixed at no charge to you.
Problem symptoms:
- Laptop randomly shuts down without any warning.
- Power LED and battery charge LED start flickering when you wiggle the power cord or the AC adapter tip on the back or your laptop.
- The battery will not get charged.
- When you plug AC adapter, the laptop appears to be dead and there is no LED activity at all (DC-IN jack on the system board is broken).
To fix the problem, you have to take your laptop apart, remove the system board to resoleder or replace the DC-IN jack. Toshiba Satellite M35X and Toshiba Satellite A70/A75 disassembly guides will help you to remove the system board. Take a closer look at the power jack on the system board with a magnifying glass. In most cases you get the power problem because of a bad connection between the DC jack and the system board, you’ll see a crack between the DC jack connector and the system board.
Here is an example of Toshiba Satellite M35X power jack. The crack occurs between the DC jack pin and the system board.
In some cases the connection is good, but the DC jack is bad itself. You can find a new DC jack for Toshiba Satellite M35X and Toshiba Satellite A70/A75 laptops here. Search for DC jack M35X or DC jack A75.
How to resolder laptop power jack yourself.
UPDATE:
Sometimes, after you replace the jack, you can see that the system board doesn’t get power at all. The battery will not charge and the power LED will not light when you plug in the AC adapter. So, here’s a possible explanation.
When a connection between the positive pin and the motherboard breaks (cracks), the power jack gets loose. You can feel it when you plug in the adapter plug. A loose power jack can damage the trace inside the hole in the system board. Take a look at the picture.
As you see, the positive pin goes through the hole in the system board and you solder it on the top side. Right? What if the trace between the top side and the bottom side is broken somewhere inside the hole? I’ve seen it before a few times. In this case everything looks nice and clean on the top side. When you plug in the AC adapter, you get normal voltage readings between “+” and “-“ pins on the top side, but the power DOESN’T go to the motherboard at all, because there is no connection between the top and bottom sides. Test with a multimeter if there is a connection between the top and the bottom.
If the trace inside the hole is broken you still can fix it. You can run a wire to connect the top and the bottom sides. Be careful not to short something on the board.
Update:
Here’s another solution to fix the power jack problem, it shows how to relocate the power jack outside the laptop base. Check it out here: Toshiba Satellite A75 failed power jack workaround.
When you repair a loose power jack, it’s a good idea to check the jack on both sides of the motherboard. When you remove the top cover from a Toshiba Satellite A70/A75 laptop you can see only points where the jack is soldered to the motherboard as it shown on the second picture in this post, but you cannot see the jack itself as it shown on the first picture.
Removing the motherboard from Satellite A70/A75 laptop is a good idea because the jack itself might has a broken “+” pin, as it shown on the picture below. If the “+” broke off the base, you’ll have to replace the jack.
UPDATE:
Today I received another well written and well documented guide about fixing Toshiba Satellite M35X power connector issue. This guide was submitted by Stephen Macuch. Thank you Stephen for great pictures and detailed instructions.
If you are tired of fixing your laptop and want to sell it for parts you can do it here:
Any Notebook Part - free classifieds. Only laptop stuff.
Entry Filed under: Toshiba Laptop Problems
602 Responses to “Toshiba Satellite M35X and Satellite A75 power jack and battery charge problem”
Pages: « 61 … 59 58 57 56 55 [54] 53 52 51 50 49 … 1 » Show All
Pages: « 61 … 59 58 57 56 55 [54] 53 52 51 50 49 … 1 » Show All
March 18th, 2008 at 6:01 am
i’ve tried with the vga port and is the same thing. is enough a little pressure on the corner (near the fan) in any direction for allow the laptop to boot. i’m sure that is a little problem, but is very hard to find!
March 18th, 2008 at 5:40 am
hi c/2600 and thanks for the answer. i think that you are right!
i’ve tried to press on the MB in the corner instead to press the jack and is boot the toshiba logo anyhow.
i think also that is the MB damaged (some trace break or some component unsoldered. Yes, but which one!? ) because i have to press on the motherboard in order to boot the laptop, else the laptop seem to go in the protection state.
now i’ll try with the VGA port, but i think that is the same.
if the problem is the MB ought to trash it? is there any solution?
thanks!!
March 16th, 2008 at 7:40 pm
Randy,
Did you test your laptops with an external monitor? Did you test the power supply?
As I mentioned in my previous comment, all you need is main board, CPU and memory. With these three part you should be able to boot the laptop to the Toshiba logo. If the laptop gets power and power LED lights up, but nothing appears on the screen (internal or external), check the memory first. Try installing another working module. If it doesn’t help, probably you have dead main board.
March 16th, 2008 at 7:35 pm
Peps,
I don’t think that this problem is related to the power jack.
You can try assembling the notebook outside the case. All you need is motherboard, CPU with heatsink, memory and power switch board. Assemble this system on your desk, plug in an external monitor into the VGA port, connect the power adapter and turn it on.
Does it boot to the Toshiba logo on the external monitor? If you have to press on the motherboard in order to boot the laptop, apparently there is a problem with the motherboard.
I have a Toshiba Satellite M35X laptop with a similar problem under my bench. It boots only if I apply some pressure on the motherboard. In my case it’s a problem with the motherboard.
March 16th, 2008 at 11:08 am
Hi, my employer was going to toss two full laptops into the trash. I asked if i could have them and see if i could get them working.
Toshiba Satellite A75-S206
I have gone through the power/DC jacks like the instructions here say and still no power to anything.
on one I did the external modification and nothing.
Is there anything else i should be aware of to bring power into these things? Something else i can try?
where can i find a cheap/inexpensive supply of motherboards?
March 16th, 2008 at 6:59 am
hi!
in order at all sorry for my english!
I’ve a Toshiba satellite m30x-128 and i’ve problem with DC jack. i’ve soldered the jack in the both side, but the notebook start only if i push strongly the connector. else the note start but after few seconds stop itself, but don’t switch off itself completely.
now i’ve unsolder the jack and i’ve seen that there isn’t any trace in the “top side”, under the solder point.
wath i must do? there is anything connected on the top side solder? help me please! thanks!
March 9th, 2008 at 8:38 pm
I have a HP Pavillion dv4000. Ihave two cracks on the outer case near the hinges. The computer is still operable. I talked with an HP tech. and they have not received a report of this type problem with the pavillion dv4000 model. Does anyone have knowledge of this type problem?
March 8th, 2008 at 2:35 pm
Hi, i had to take apart my A75 to re-set the power button, now the thing wont turn on! When I plug in the laptop the green and orange lights (plug & battery lights) flash once, it is not a long flash, its like a single blink. And the battery will not charge.
March 7th, 2008 at 6:04 pm
thanks for the tut. I actually had to fix the dc jack twice because the first time I used wires that were too thin. The second time I used wires with the recommended gauge and I haven’t had any problems yet. However, now the manual volume dial is broken and I’m trying to look for parts to repair it.
March 6th, 2008 at 10:31 pm
Nina,
Here you’ll find instructions for taking apart Toshiba laptops.