You replaced the broken LCD screen in your laptop with a new screen but it’s not working. Does this sound like your problem? Let’s find out what could be wrong and how you can fix it.
First of all, I assume that your new LCD screen is compatible with the old one. Different screens require different video cables. Make sure you new screen is compatible with your laptop.
OK, let’s say you accidentally damaged the LCD screen in your laptop. A part of the screen still works fine but you cannot use it like that so you decided to replace the screen yourself. You can find LCD replacement instructions in service manuals or this DIY site.
You did some research and purchased a compatible screen, installed it into the laptop, turned it on and… The new screen is not working!!! What could be wrong?
Before you start to panic, check all cable connections again. Check connection between the video cable, LCD screen and inverter board. Reconnect cables just in case.
Take a closer look at the connection between the video cable and LCD screen. It’s possible you accidentally pulled the video cable from the connector during the screen installation.
The video cable has to be seated properly, all the way down.
Also, on some older LCD screens there are very thin pins inside the connector. Take a look inside the connector, make sure there are no damaged (bent) pins.
You can straighten bent pins with a very small screwdriver but this procedure requires a lot of patience and concentration.
Fortunately, most newer LCDs have a different type of connector, without fragile pins inside.
OK, you have reseated all connectors and cannot see anything wrong but the new screen still is not working. What’s next?
Remove the new screen and connect the old one. If the old one works properly (except the damaged area) but the new one is dead, apparently the new screen is defective and has to be replaced. Hopefully it has warranty.
Here’s another scenario. The new screen kinda works. You can see a very faint image but there is no backlight.
If that’s the case, disconnect the new screen from the inverter board and plug in the old screen instead, as it shown on the picture below. If the backlight inside the old screen lights up, apparently the new screen has defective backlight lamp and has to be replaced.
Related post: Laptop has bad video on the LCD screen. What is wrong?
If you find this article useful, please consider making a donation to the author. Thank you!
May 2nd, 2010 at 10:48 am
toshiba laptop screen broken how much will it be reply back soon as please
April 24th, 2010 at 2:09 pm
Rob,
If you are getting image on the old cracked screen but not on the new one, most likely your new screen either not compatible or defective.
Contact the seller, explain that your cracked screen still works but the new one doesn’t and ask them to replace the screen.
April 24th, 2010 at 1:43 pm
Yes i tried the old screen and it comes right on but i can only see the top 20% so i cant use it for much.I feel sure I have the correct screen I did my home work and sent the compony I bought it from all the info and even called to make sure everything matched up.
April 24th, 2010 at 12:32 pm
Rob,
Did you get any image on the undamaged part of the cracked screen? If you did, can you install the cracked screen back and see if the image is still there?
Are you sure that your new screen is compatible with the laptop?
April 24th, 2010 at 7:28 am
I just replaced a crecked screen on my dell xps 1530 the back light comes on but nothing? do i need to load a driver? ive check all conections 8 time. please help
April 8th, 2010 at 4:40 pm
just replaced screen on sony vaio pcg 7112L turn it on and screen is red but you caan see a picture. it does not turn red with old screen if i tap on bottom of case near battery or push pressure then the true pic comes on. as soon as i move my hand it goes red and other colors again. the company i bought it from says its compatible. at the top of the screen where the ribbon hooks into the circuit board there is a large connector and a small connector. on old screen it only has one connector pls help.
April 3rd, 2010 at 11:40 am
Hi, I just replaced my broken screen on Hp dv 2000. After I turn the laptop on the screen just glows white. I don’t know what the problem is and what this means.
March 14th, 2010 at 7:01 pm
I recently replaced the screens on to seperate V6000 Laptops doing so I damaged one of the inverter boards(somehow bent 2 of the 6 prongs in the plug on the card). So I went ahead and replaced both inverters as well. One lap top (wifes) seems to work fine. Although its not used very often. The other one (mine) sometimes the inverter needs to be unplugged and plugged back in after a rebooting or when I wake it from sleep mode. I tried switching inverters. This makes no difference.
Any Ideas ???
March 6th, 2010 at 4:52 pm
Philips h12y (Vista) – old chimei screen damaged – part viewable. merchant says new LG screen compatible – but just get white screen – external monitor fine. Put old screen back – now also just white (both can be turned off with Fn/F3 keys). Double checked connections at both ends, cable doesn’t appear damaged Do I change inverter and/or cable? If new screen incompatible, has it done any irreversible damage? How can I check if LG screen is truly compatible (with inverter?)?
March 4th, 2010 at 9:30 am
Excellent doc, i had similar problem with my laptop and rectified the same.
Thanks for nice work!!
Cheers