This guide will explain how to repair a failed or loose DC power jack on a laptop computer yourself.

Disclaimer: I’ve made these instructions only for people experienced with soldering and repairing computers. If you don’t feel comfortable doing this job, please do not open the laptop or you can permanently damage your computer. Take your laptop to a professional repair shop instead.
Use this repair guide at your own risk. :)

For this repair you’ll need the following tools.

1. Soldering iron or soldering station. I use Weller WES51 soldering station and for this job I set temperature to about 800-850°F.
2. I use high-tech rosin core silver-bearing solder from Radioshack with diameter 0.022″ ( Catalog #: 64-013 ). I think standard rosin core solder will work just fine.
3. Desoldering pump for removing solder around component leads. I use Edsyn Soldapullt pump, model DS 017.
4. 99% isopropyl alcohol and tooth brush for cleaning the motherboard from flux.
5. A new DC power jack.

DC jack repair tools

Laptop DC power jack repair guide.

Laptop DC power jack

As you see on the following picture, the solder drop on the positive terminal looks different than on other three contacts. That’s where the problem is. The positive pin is not making a good contact with the motherboard and because of that power to the laptop cuts off when I move the power plug inside the power jack.
I’m going to desolder the power jack from the motherboard, clean contacts on both power jack and motherboard and then solder it back in place – this is the proper way fixing the power problem.

DC power jack bottom side

Start desoldering process with adding some new fresh solder to all three contacts. This will make old solder more flowable, easier to remove.

Removing solder

While heating one of the contacts, remove the solder from this contact using the desoldering pump. Repeat the same steps with all power jack contacts until you remove as much solder as possible.

Sucking extra solder

Grab the power jack and carefully try removing it from the motherboard. Most likely you will not be able to remove the power jack the first time because there will be some solder bridges left between the contacts and traces on the motherboard. Carefully wiggle the power jack without applying any significant force and at the same time heat up all contacts one by one. This will help you to remove the power jack.

Remove DC power jack

The DC power jack is almost removed from the motherboard.
Be careful. Inside the positive hole there is a copper sleeve which connects the terminal on one side of the motherboard with the traces on the other side. If you are removing the power jack with force, you can pull the sleeve from the hole. You don’t want to do that.

UPDATE: If you accidentally removed the internal sleeve, check out this post: How to fortify damaged power jack connection.

So, do not apply any force and make sure the solder is melted when you are removing the power jack. I hope you understand what I’m talking about.

Separating jack from motherboard

After the power jack is removed, clean all oxidized contacts with a knife.

Cleaning power jack contacts

Apply a fresh coat of solder to all contacts on the power jack.

Coating contacts

The power jack terminals will look dirty because of melted flux.

Flux on motherboard

You can remove the flux using the tooth brush and alcohol. It’s not necessary but it will make your job looking clean.

Removing extra flux

Apply a fresh coat of solder to all power jack terminals on both sides of the motherboard.

Coating contacts

This side has been coated.

Cleaned contacts side 1

And this side has been coated too.

Cleaned contacts side 2

Now you can install the power jack back on the motherboard. Put something under power jack so there is no gap between the jack and the motherboard. Now you are ready to solder the jack back in place.

DC power jack installed

Solder all power jack pins.

Soldering power jack

The job is done and the laptop DC power jack is fixed. B-E-A-utiful!
Now just install the motherboard back into the laptop and you are done.

DC power jack fixed

Support this site.



Pages: [53] 52 51 50 49 48 47 46 45 44 431 » Show All

  1. 523
    cj2600 Says:

    @ Manuel Zamora,
    I think you’ll get better results if the jack is removed and legs cleaned up. It will make a better contact with the motherboard this way and will be more solid. It’s my opinion.

  2. 522
    Manuel Zamora Says:

    For this repair, the bad solder point could have just been redone, no need to remove the entire jack. Some flux, removal of old solder on bad point, fresh solder (with flux)and it would have been good as new. The only time the entire jack needs to be removed is if the actual DC jack is bad, cracked, inside is broken. This one was as easy as they get, just resolder without removal.

  3. 521
    need simple Says:

    do I fix, spend $100 to have fixed or just buy a new computer- anything but HP. to date I have only bought HP becuase they could always talk me into the brand. this last one I bought directly from HP and had no luck getting any service or replacment of the junk. I have had to attempt fixing myself

  4. 520
    James Says:

    Dude, i just need to thank you very much.
    I was looking for something like this by months, but on my country there is nothing about it.
    So thank you dude, you saved my motherboard.

  5. 519
    victor diaz Says:

    I bought another one – (hp pavilion zv5000)thinking to swap the hard drive, but then the power port went on it too. hp is the culprit for a poor design… so now I have 2 paper weights. I took a stab at di-assembling one, but I am not confident that I can put it back together.

  6. 518
    Atten Says:

    Better to use a soldering station other than a solder gun for this job.

  7. 517
    TerryLee Renner Says:

    I wish to thank you for your site. I was unable to dismantle the case halves due to the 2 screws under the keyboard that I didn’t know existed. I’m very happy to have found your tutorial; well thought -out and easy to see. Toshiba T115D . I installed my own version of a new power jack and cable using RCA gold connectors and longer leads. The nut for the jack itself is hard-soldered to the inside surface of a stainless steel clip, channel-shaped, which slides over the bottom lip of the original jack opening, along with the black lead. Only the red lead is attached to the jack itself. This allows me to unfasten the jack from the case without removing anything, should it fail again.

  8. 516
    Francis Says:

    Thank you so much. This is the best and most helpfull teaching lessons I have ever come accross. Once more, thank you and keep it up.

  9. 515
    cj2600 Says:

    @ drew,

    Check memory modules. Make sure both memory modules seated correctly. Try reseating them.
    Check the video cable connection. Make sure the video cable properly plugged into the motherboard. Try reseating the cable connector.

  10. 514
    drew Says:

    I followed steps above and replaced dc jack in motherboard
    I reassembled medion notebook and upon starting the computer
    the screen was completley distorted.
    possible to advise where things might have went wrong and how it
    may be corrected?
    thank you

Pages: [53] 52 51 50 49 48 47 46 45 44 431 » Show All

Leave a Reply